Utforska de här idéerna och mycket mer!

Utforska relaterade ämnen

You always wanted a 3D Printer but they Cost Way To Much? Then enter this Giveaway to be in the run for a New Anet A8 3D Printer.

You always wanted a 3D Printer but they Cost Way To Much? Then enter this Giveaway to be in the run for a New Anet A8 3D Printer.

Win Jason Scheff's Bass Guitar (Lead singer and bassist with the band Chicago)

Win Jason Scheff's Bass Guitar (Lead singer and bassist with the band Chicago)

Ender -  $179,99 (coupon GBENDER ) #3D, #Printer, #Ender

Ender - $179,99 (coupon GBENDER ) #3D, #Printer, #Ender

ANT Ecarry 3D Printer

ANT Ecarry 3D Printer

I remixed this thing to fit my Anet A8 which has the "stiffi" style frame brace. I had to cut a section out on the side of the case and lid due to the lower support of the frame brace. I also opened up the hole for the 80mm fan so there is no restricted air flow. I added a fan cover from the power supply cover. As you can also see in the photo's I had to cut about 6mm off the end of the heat sink on the mosfet as it was preventing the cover from installing correctly. This should...

I remixed this thing to fit my Anet A8 which has the "stiffi" style frame brace. I had to cut a section out on the side of the case and lid due to the lower support of the frame brace. I also opened up the hole for the 80mm fan so there is no restricted air flow. I added a fan cover from the power supply cover. As you can also see in the photo's I had to cut about 6mm off the end of the heat sink on the mosfet as it was preventing the cover from installing correctly. This should...

This holder will mound the sensor much nearly to the extruder. That will enlarge the usable part of the hotbed and will be more exact measurements as with the original plexiglas plate from manufactor. The benefit against holder like these (http://www.thingiverse.com/thing:1977941) is, that you can unmount the Fan to change the filament without a new calibration of the sensor position. I bougt the sensor from here, in reason the needed plug for Anet 1.0 Mainboard is already adde...

This holder will mound the sensor much nearly to the extruder. That will enlarge the usable part of the hotbed and will be more exact measurements as with the original plexiglas plate from manufactor. The benefit against holder like these (http://www.thingiverse.com/thing:1977941) is, that you can unmount the Fan to change the filament without a new calibration of the sensor position. I bougt the sensor from here, in reason the needed plug for Anet 1.0 Mainboard is already adde...

Win Nintendo Switch Giveaway June 2017

Win Nintendo Switch Giveaway June 2017

Anet A6 3D принтер reprap prusa i3, новая версия 2017 года, высокая точность печати,16 ГБ карта памяти пластик для теста в подарок, сопла на разных диаметры, доставка из Москвы купить на AliExpress

Anet A6 3D принтер reprap prusa i3, новая версия 2017 года, высокая точность печати,16 ГБ карта памяти пластик для теста в подарок, сопла на разных диаметры, доставка из Москвы купить на AliExpress

Anet A8 3D Printer Prusa i3 DIY Kit - Multiple Filament Types, Large Printing Volume, 0.004mm Precision, SD Card Slot - Anet A8 3D Printer Prusa i3 DIY Kit offers an affordable way to assemble your own cheap 3D printer. Print anything you can imagine in great detail and quality.

Anet A8 3D Printer Prusa i3 DIY Kit - Multiple Filament Types, Large Printing Volume, 0.004mm Precision, SD Card Slot - Anet A8 3D Printer Prusa i3 DIY Kit offers an affordable way to assemble your own cheap 3D printer. Print anything you can imagine in great detail and quality.

Pinterest
Sök